产品与服务

Test item

Clause

Test Principle/Requirement(s)

Comment

Edges and corners

Clause 5.1

For seating, the edges and corners of the seat, back rest and arm rests which are directly in contact with the user when sitting , lying or reclining shall be rounded or chamfered.

For table tops the edges and corners which are directly in contact with the user shall be rounded or chamfered.

All other edges and corners of seating and tables, accessible during use shall be free from burrs or/and sharp edges.

Tubular components, holes and gaps accessible during use

Clause 5.2

Tubular components, holes and gaps accessible during use shall be covered if a7mmor12mmtest probe can be pushed into them in any direction with a maximum force of 30N to a depth of more than10mmand cannot be pulled out again in the reverse direction by a maximum force of 30N.

Bottom of tubular legs shall be capped or plugged.

Test item

Clause

Test Principle/Requirement(s)

Comment

Sheer and squeeze points

Clause 5.3

5.3.1Shear and squeeze points when setting up and folding

Unless5.3.2 and 5.3.3 are applicable, Shear and squeeze points that are created only during setting up or folding are acceptable providing the user can be assumed to be in control of his /her movements and to be able to cease applying the force immediately on experiencing pain.

The edges of parts moving relative to each other and creating

Shear and squeeze points under the influence of powered mechanisms Shear and squeeze points shall be as specified in 5.1

5.3.2Shear and squeeze points under the influence of powered mechanisms

These shall be no accessible shear and squeeze points created by parts of furniture operated by powered mechanisms, e.g. mechanical springs, gas lifts.

5.3.3There shall be no accessible shear and squeeze points created by loads applied during normal use.

For seating, the loads applied during normal use can be found in ENV581-2, and for tables in EN 581-3.

Shear and squeeze points are not acceptable if a hazard is created by the weight of user during the normal movements and actions, e.g. attempting to move the seating by lifting the seat or by adjusting the backrest.

Test item

Clause

Test parameters

Comment

Domestic

Seat and back static load test

EN 1728:20006.2.1

Seat :force N

10×10s(±2s)+1×30 min(±10s)

Back :force N

10×10s(±2s)+1×30 min(±10s)

1600

410

Seat front edge static load test

EN 1728:20006.2.2

Force, N

10×10s(±2s)+1×30 min(±10s)

1300

Seat and back fatigue test for seating

EN 1728:2000 6.7

Cycles

Seat : force, N

Back bending moment

N.m

25000

1000

100 max

Fatigue test on back rest mechanism

See Annex A

Cycles

Seat : Load, kg

Force, N

Back bending moment

N.m

10000

100

250

100

Arm downwards

static load test

EN 1728:2000 6.6

Vertical force, N

700

Arm fatigue test

EN 1728:2000 6.10

Cycles

Force, N

10000

400

Leg forward static load test

EN 1728:2000 6.12

Seat : Load, kg

Horizontal force, N

75

300

Leg sideways static load test

EN 1728:2000 6.13

Seat : Load, kg

Horizontal force, N

75

300

Seat impact test

EN 1728:2000 6.15

Drop height, mm

10 times

180

Foot rail static test for high seating

EN 1728:2000 6.4

Vertical force, N

1000

Test item

Clause

Test parameters

Comment

Forward stability

EN 1022:2005 6.2

Vertical force ,N

Horizontal force, N

t≥5s

600

20

Sideways overbalancing, all seating without arms

EN 1022:2005 6.4

Vertical force , N

Horizontal force, N

t≥5s

600

20

Sideways overbalancing , all seating with arms

EN 1022:2005 6.5

Vertically force for the seat : N

Vertically force for the arms : N

Horizontally force for the side of the arms: N 

t≥5s

250

350

20

Rearwards

stability

EN 1022:2005 6.6

Vertical force ,N

Horizontal force:

t≥5s

600

F=80N H≥720mmF=0.2857(1000-H)N H＜720 mm

Instruction for use(visual check)

Clause 7.1 General

Name and address of the producer (manufacturer or supplier);

Information regarding maintenance;

Condition for use of the product (camping, domestic or contract).

Clause7.2 Marking for mobile loungers

All mobile loungers not intended to be lifted and moved under the load specified in Table B.1 shall be marked

with a pictogram as an example is shown in Figure 1